JVC Speaker TS C500SPG User Manual

SPEAKER UNIT  
INSTALLATIONANLEITUNG :LAUTSPRECHEREINHEIT  
MANUEL D’INSTALLATION :ENCEINTE  
MANUALE D’INSTALLAZIONE :UNITÀ DI DIFFUSIONE  
MANUAL DE INSTALACION  
:UNIDAD DE ALTAVOZ  
:
INSTALLATION MANUAL  
TS-C500SPG  
SPEAKER UNIT FOR A JVC PLASMA DISPLAY MONITOR  
LAUTSPRECHEREINHEIT FÜR JVC PLASMA BILDSCHIRM  
ENCEINTE POUR UN MONITEUR DE VISUALISATION PLASMA  
UNITÀ DI DIFFUSIONE PER MONITOR CON SCHERMO AL PLASMA JVC  
UNIDAD DE ALTAVOZ PARA MONITOR PLASMA DISPLAY JVC  
LCT1635-001A  
 
Attaching the front speakers to the GM-X50 series display  
Using the speaker brackets, you can attach the front speakers to the side of the display.  
• Do not loosen the screws other than the protective screws.  
• Use only the supplied mounting screws for attaching the front speakers.  
1. Remove the protective screws on the back of the display  
with phillips screwdriver.  
Protective  
screw  
Protective  
screw  
2. Attach the front speaker to the back of the display.  
1 Turn the mounting screws with phillips  
2 Hook the speaker bracket onto three mounting screws  
screwdriver, leaving a length of about 3 mm.  
through the screw holes (A), and slide it down.  
Screw hole (A)  
3. Tighten the mounting screws firmly with phillips screwdriver.  
• When moving the display, do not hold the speakers.  
• The speakers are not of anti-magnetic type.  
Do not place anything susceptible to magnetism, such as a video tape, nearby when setting the speakers.  
2
 
Connecting the speaker cord  
Attach to the speakers  
When you connect the supplied speaker cord to the terminal clamp of the speakers, fold the end of each speaker  
cord to avoid short-circuit.  
1. Fold the end of each speaker  
cord.  
2. Press and hold the terminal  
clamp.  
3. Insert the speaker cord, and  
release the finger from the  
terminal clamp.  
• Connect the cord with black stripes to the · (black) terminal and the other cord to the ª (red) terminal.  
• Be careful that connection of the speaker cords to incorrect polarity terminals (ª and ·) degrades stereo  
feeling and sound qualities.  
Attach to the display  
1. Open the terminal clamp.  
2. Insert the speaker cord.  
3. Close the terminal clamp.  
• Connect the cord with black stripes to the · (black) terminal and the other cord to the ª (red) terminal.  
• Be careful that connection of the speaker cords to incorrect polarity terminals (ª and ·) degrades stereo  
feeling and sound qualities.  
• Attach the ferrite core supplied with your display to the speaker cord.  
For details, refer to the instruction manual of your display.  
Bundling the speaker cords  
You can bundle the speaker cords neatly with the supplied cord clamp, as illustrated.  
Cord clamp  
• Stick the cord clamp firmly after removing its protective seal.  
• When sticking the cord clamp on the display:  
— Make sure not to block the ventilation hole.  
— Make sure not to prevent attachment of the options, such as a Wall Mounting Unit or  
a Ceiling Suspension Unit.  
Speaker cord  
3
 
Specifications  
• Power Handling Capacity : 3 W  
• Impedance  
• Speaker  
: 6   
: 9.5 cm x 1 cm  
Direct Drive Speaker, two  
• Dimensions  
(W x H x D)  
(Mass)  
: 42 mm x 740.5 mm x 54 mm  
: 0.9 kg (for each excluding the speaker bracket)  
Top view  
Front view  
Side view  
Unit: mm  
4
 
VICTOR COMPANY OF JAPAN, LIMITED  
© 2004 VICTOR COMPANY OF JAPAN, LIMITED  
 
0204MKH-MW  

Ingersoll Rand Outboard Motor 8274 A 8276 A User Manual
InStep Stroller 11 KS288 User Manual
Intel Network Card SBC83675 User Manual
Intel Server S5500HCV User Manual
Jabra Bluetooth Headset BT2090 User Manual
JVC CRT Television HV 29JH24 HV 29JH54 HV 29JH74 HV 29VH14 HV 29JH54 User Manual
JVC Speaker System CA UXL30R User Manual
Keating Of Chicago Fryer 20 BB Electric User Manual
Kenmore Microwave Oven 87039 User Manual
Kodak Automobile Accessories K7600 C User Manual