Korg Musical Instrument D1200mkii User Manual

Burning Audio CDs – D12, D1200 (mkII), D16 and D1600(mkII)  
The D12, D16 and D1600 allow the user to create a standard audio CD using an external SCSI  
CDR/RW burner or, in the case of the D12, D1200 and D1600, an optional internal CDR/RW burner.  
The D-series recorders burn the data that is currently on tracks 1 and 2, so that means if one wishes  
to burn an entire mix, it would have to be first bounced to those two tracks.  
“But what if I already have data on tracks 1 and 2?” The good news is that the entire mix (including  
the data that’s already on tracks 1 & 2) can be recorded or “bounced” without losing tracks 1 and 2.  
This info is simply merged together. This tutorial explains how to bounce the tracks and burn an  
audio CD.  
First, we’ll bounce the mix down to Tracks 1 & 2:  
1.  
2.  
Set up your mix. Adjust the faders, pan pots, effects and scenes.  
Press the RECORD button (the square one just right of the screen) so that the screen displays the  
Record Mode.  
3.  
4.  
5.  
Using the cursor buttons, highlight “Bounce” and press the ENTER button.  
Press the RECORD button to enter the Bounce Mode.  
Using the cursor buttons once again, highlight “16Tr Æ 2Tr” (or “12Tr2Tr in D12”) and press the  
ENTER button.  
6.  
Cursor down to Record Virtual Track and select a virtual track to record on. For this tutorial we will  
select virtual track h.  
7.  
8.  
Put tracks 1 & 2 into record ready mode (LEDs are red).  
Press the METER/TRACK VIEW button, to monitor the signals. The level of the L/R Master will  
mirror what’s going into tracks 1& 2.  
9.  
Rewind to the start of your song and press the REC and PLAY to record the whole song. When  
done press stop.  
10.  
11.  
Upon completion, press the TRACK button to enter the Vtr1-8 (Vtr1-6 on the D12) screen.  
Using the cursor button highlight 1a then using the value wheel, select virtual track 1h. Do the same  
for track 2a (set to 2h).  
12.  
13.  
Set the pan pots for tracks 1 & 2 left and right respectively, and set the faders to unity (0dB).  
Repeat steps 1-12 for every song that you wish to put to CD.  
Now we’re ready to burn tracks 1 and 2 to CD. Set Scene Read to OFF at this point, so that tracks 1  
and 2 cannot be manipulated as they were when they were single tracks. If you have not already done  
so, insert a blank CDR into the drive and allow it to ‘spin up’ completely, then:  
1.  
2.  
Press the SONG/CD button until you reach the Song Select screen. Note, the song you select on this  
screen is the one that will be burned to the CD.  
Press the SONG/CD button (on the D16 the SONG button) three times to enter the CDR/RW  
screen.  
 

Invacare Wheelchair E1028 User Manual
JBL Speaker HTI55 User Manual
JobSite Systems Stereo Amplifier AB50 X2 User Manual
John Deere Impact Driver AT 3104 J User Manual
JVC Projector AV P720U User Manual
Jwin Car Stereo System JC CD260 User Manual
KitchenAid Dishwasher 8573754 User Manual
KitchenAid Dishwasher KUDC02IR User Manual
KitchenAid Food Processor 4KFC3100BU2 User Manual
KitchenAid Indoor Furnishings KKFV01LPCR User Manual