Kenwood Home Theater System RFU 6100 User Manual

RFU-6100  
and degrade the system’s perform-  
ance.  
Congratulations!  
RF Receiver Connections  
The Kenwood Fineline™ RFU-6100 RF Wireless System eliminates the long wires that run from  
your A/V receiver to your surround speakers. Our RF wireless technology works with any  
conventional surround speaker, so you are free to choose any brand and model of surround  
speaker, or you can use it with surround speakers that you already own. This sheet explains  
how to connect and set up the system’s RF transmitter and RF receiver units.  
• To minimize interference, place  
the RF transmitter away from  
your A/V receiver and TV.  
Left Surround  
Speaker  
Right Surround  
Speaker  
4. Connect the left & right surround  
speakers to the RF receiver as  
shown in the diagram to the left.  
Setting Up the Wireless System  
• Connect the terminal with the  
blue lever to the left surround  
speaker; connect the terminal  
with the gray lever to the right  
surround speaker.  
1. Connect  
the  
RF  
transmitter’s speaker  
wires as shown in the  
diagram to the right.  
RF Transmitter Connections  
Connect  
the speaker's "  
"
+
(red) terminal  
to the receiver's  
• Connect the wire  
with the blue lead to  
the A/V receiver’s  
Left Surround speak-  
er output’s “+” termi-  
nal; connect the wire  
with the gray lead to  
the A/V receiver’s  
colored connector  
• Make sure to connect the “+” ter-  
minals on the RF receiver to the  
“+” terminals on the speakers.  
5. Place the RF receiver at least one  
foot off the ground. Avoid placing it  
close to large metal objects like  
radiators or heating/air condition-  
ing ducts. These objects can  
absorb RF signals and degrade the  
system’s performance.  
Right  
Surround  
speaker output’s “+”  
terminal.  
Blue  
Wire  
Gray  
Wire  
• To minimize interference, place  
the RF receiver away from your  
A/V receiver and TV.  
RFU-6100 RF Receiver  
NOTE: The transmitter  
can be used with A/V  
receivers with a sur-  
round channel power  
rating of up to 120  
watts per channel.  
Use with surround  
channel power of  
more than 120 watts  
per channel may  
cause audible distortion.  
RFU-6100T RF Transmitter  
6. Make sure that the RF channel  
switches on the transmitter and  
receiver are both set to the same  
channel (see the diagram to the right).  
RF Channel Selection  
7. Plug the RF receiver’s AC cord and  
the RF transmitter’s power adapter  
into a wall outlet..  
8. Extend the antennas on both units  
as needed to improve reception.  
2. Connect the supplied power supply adapter as shown in the diagram above.  
Important: Do not plug the power adapter into the wall outlet until you have made  
all of the RF transmitter and RF receiver connections (Step 7).  
9. If reception is poor or there is inter-  
ference, change the RF channel on  
3. Place the RF transmitter at least one foot off the ground. Avoid placing it close to large metal  
objects like radiators or heating/air conditioning ducts. These objects can absorb RF signals  
the transmitter and receiver as shown in the diagram to the right.  
• Make sure both units are set to the same RF channel.  
Kenwood FinelineQuick Start Guide  
If you have any questions about your new system, please contact our Customer Service Department at  
Copyright ©2004 Kenwood USA Corporation. All rights reserved.  
 
032-0604 6100 QSG  

Indesit Dishwasher DE 43 User Manual
InStep Stroller 11 BA202 User Manual
Invacare Hot Tub 1154272 User Manual
JL Audio Car Speaker SB VW NB 10W3 User Manual
Kenmore Water Dispenser 625345500 User Manual
Kenmore Water Heater 153331492 User Manual
Kenwood Stereo System TK 3230K User Manual
Kettler Baby Gym Art Nr 07426 700 User Manual
KitchenAid Cooktop W10526088A User Manual
Kodak DVD Player MP6000 User Manual