Insignia TV Mount NS TVMFP23 User Manual

INSTALLATION GUIDE  
FIXED-POSITION WALL MOUNT FOR TVs 40-70 in.  
NS-TVMFP23/NS-TVMFP23-C  
Safety information and specifications . . .2  
Tools needed. . . . . . . . . . . . . . . . . . . . . . . . . . .3  
Package contents . . . . . . . . . . . . . . . . . . . . . .3  
Installation instructions. . . . . . . . . . . . . . . . .5  
For either wood-stud or  
concrete wall installations  
Before using your new product, please read these instructions to prevent any damage.  
 
FIXED-POSITION WALL MOUNT FOR TVs 40-70 in.  
Tools needed  
You will need the following tools to assemble your new TV wall mount:  
ardware  
Socket wrench with 1/2 in.  
(13 mm) socket or adjustable  
wrench  
Edge-to-edge  
stud finder  
Drill  
Phillips screwdriver  
7/32 in. (5.5 mm) wood  
Hammer  
Level  
drill bit for wood stud wall  
OR  
3/8 in. (10 mm) masonry  
drill bit (for concrete wall)  
Tape  
Measuring tape  
Package contents  
Make sure that you have all the hardware necessary to assemble your new TV wall mount:  
A Wall Plate (1)  
C Right TV Bracket (1)  
B Left TV Bracket (1)  
R Wall Plate Template (1)  
A
B
C
R
3
 
   
FIXED-POSITION WALL MOUNT FOR TVs 40-70 in.  
TV Hardware Bag  
Label  
D
Hardware  
Qty.  
Label  
K
Hardware  
Qty.  
4
M5 × 12 mm  
screw  
4
4
M6 × 35 mm  
screw  
M5 × 35 mm  
screw  
E
F
M8 × 16 mm  
screw  
L
4
4
M5 washer  
4
4
M8 × 20 mm  
screw  
M
M6/M8 washer  
G
M8 × 35 mm  
screw  
N
O
P
4
4
4
H
I
4
4
4
Spacers  
Lag bolt washer  
M6 × 12 mm  
screw  
5/16 in. × 2 3/4 in. lag bolt  
M6 × 20 mm  
screw  
J
1
2
3
4in  
10  
20  
30  
40  
50  
60  
70  
80  
90  
100mm  
4
 
FIXED-POSITION WALL MOUNT FOR TVs 40-70 in.  
Installation instructions  
STEP 1 - Determine whether your TV has a flat back or an  
irregular or obstructed back  
1
Carefully place your TV screen face-down on a cushioned, clean surface to protect the screen from  
damages and scratches.  
2
If your TV has a table-top stand attached, remove the stand. See the documentation that came with your  
TV for instructions.  
3
4
5
Temporarily lay the TV brackets (B and C) on the back of your TV.  
Align the screw holes in the TV brackets with the mounting screw holes on your TV.  
Identify which type of back your TV may have:  
Flat back: The brackets lay flush against the back of your TV and do not block any jacks. You do not need  
spacers when assembling the wall mount.  
Obstructed back: The brackets block one or more of the jacks on the back of your TV. You will need  
spacers when assembling the wall mount.  
Irregularly-shaped back: There is a gap between a bracket and some part of the back of your TV. You  
will need spacers when assembling the wall mount.  
6
Remove the TV brackets.  
5
 
 
FIXED-POSITION WALL MOUNT FOR TVs 40-70 in.  
STEP 2 - Select screws, washers, and spacers  
1
Select the hardware for your TV (screws, washers, and spacers). A limited number of TVs come with  
mounting hardware included. (If there are screws that came with the TV, they are almost always in the  
holes on the back of the TV.) If you don't know the correct length of the mounting screws your TV  
requires, test various sizes by hand threading the screws.  
Select one of the following types of screws:  
For a TV with a flat back:  
M5 X 12mm screws (D)  
M6 X 12mm screws (I)  
M6 X 20mm screws (J)  
M8 X 16mm screws (L)  
M8 X 20mm screws (M)  
For a TV with an irregular/obstructed back:  
M5 X 35mm screws (E)  
M6 X 35mm screws (K)  
M8 X 35mm screws (N)  
Select either an M5 washer (F) or an M6/M8 washer (G)  
For an irregular or obstructed TV back, also use Spacer (H)  
CAUTION: To avoid potential personal injuries and property damage, make sure that there are  
adequate threads to secure the brackets to your TV. If you encounter resistance, stop immediately and  
contact customer service. Use the shortest screw and spacer combination to accommodate your TV. Using  
hardware that is too long may damage your TV. However, using a screw that is too short may cause your TV to  
fall from the mount.  
Screw is too  
long  
Screw is too  
short  
Screw fits  
correctly  
2
3
Remove the screws.  
For a flat back TV, go to “STEP 3 - Option 1: Attaching the mounting hardware to TVs with a flat back“ on  
page 7.  
-OR-  
For an irregular or obstructed back, go to “STEP 3 - Option 2: Attaching the mounting hardware to TVs  
with irregular or obstructed backs” on page 8.  
6
 
FIXED-POSITION WALL MOUNT FOR TVs 40-70 in.  
STEP 3 - Option 1: Attaching the mounting hardware to TVs  
with a flat back  
1
Align the left and right TV brackets (B and C) with the screw holes on the back of the TV. Make sure that  
the brackets are level.  
2
3
Install washers (F or G), and screws (D, I, J, L, or M) into the holes in the back of the TV.  
Tighten the screws until they are snug against the TV brackets. Do not over tighten.  
or  
or  
J
orMor  
You’ll need  
Screws  
or  
or  
Level  
D (4)  
J (4)  
F (4)  
I (4)  
Washers  
Phillips screwdriver  
or  
or  
B and C TV brackets  
L (4)  
M (4)  
G (4)  
7
 
FIXED-POSITION WALL MOUNT FOR TVs 40-70 in.  
STEP 3 - Option 2: Attaching the mounting hardware to TVs  
with irregular or obstructed backs  
1
2
3
Align the left and right TV brackets (B and C) with the screw holes on the back of the TV. Make sure that  
the brackets are level.  
Place spacers (H) behind the TV brackets. Place washers (F or G) over the holes in the TV brackets. Insert  
screws (E, K, or N) through the washers, TV brackets, and spacers.  
Tighten the screws until they are snug against the TV brackets. Do not over tighten.  
or  
E
or  
or  
N
You’ll need  
Washers  
Screws  
Spacers  
H (4)  
or  
or  
E (4)  
K (4)  
G (4)  
F (4)  
or  
N (4)  
Phillips screwdriver  
Level  
B and C TV  
brackets  
8
 
FIXED-POSITION WALL MOUNT FOR TVs 40-70 in.  
STEP 4 - Determine wall-mount location  
Note:  
For more detailed information on determining where to drill your holes, visit our online height-finder  
Your TV should be high enough so your eyes are level with the middle of the screen. This is normally  
40 to 60 in. from the ground.  
The center of your TV will be offset .80 in. lower than the center of the wall plate (A). Before you drill holes  
in the wall:  
1
2
Measure the distance from the bottom of your TV to the middle (half of the height of the TV). This is  
measurement a.  
Measure the distance from the floor to where you want the bottom of the TV to be placed on the wall.  
Keep in mind that the bottom of the TV should be placed above any furniture (such as entertainment  
centers or TV stands). The TV should also be above items placed on top of the furniture (like a Blu-ray  
player or cable box). This measurement is b.  
3
4
Add a + b. The total measurement is the height where you want the center of the wall plate to be on the  
wall.  
Use a pencil to mark this spot on the wall.  
a
b
You’ll need  
Pencil  
Measuring tape  
9
 
FIXED-POSITION WALL MOUNT FOR TVs 40-70 in.  
STEP 5 - Option 1: Installing on a wood stud* wall  
Note: Any drywall covering the wall must not exceed 5/8 in. (16 mm).  
1
2
Locate the stud. Verify the center of the stud with an edge-to-edge stud finder.  
Align the wall plate template (R) at the height you determined in the previous step (or by using the  
HeightFinder mentioned on the template), make sure that it is level, then tape it to the wall.  
Drill pilot holes through the template to a depth of 3 in. (75 mm) using a 7/32 in. (5.5 mm) diameter drill  
bit, then remove the template.  
Align the wall plate (A) with the pilot holes, insert the lag bolts (P) through the lag bolt washers (O),  
then through the holes in the wall plate. Tighten the lag bolts only until they are firm against the wall  
plate.  
3
4
CAUTION:  
Avoid potential injuries or property damage!  
DO NOT over-tighten the lag bolts (P).  
* Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 11/2 x 31/2 in. (38 x 89 mm).  
* Minimum horizontal spacing between fasteners cannot be less than 16 in. (406 mm).  
16-24 in.  
R
3 in.  
75 mm)  
You’ll need  
Wall plate template (R)  
O (4)  
1/2 in. socket  
wrench  
Wall plate (A)  
Edge-to edge  
stud finder  
Drill  
P (4)  
Level  
7/32 in. wood drill bit  
Tape  
10  
 
FIXED-POSITION WALL MOUNT FOR TVs 40-70 in.  
STEP 5 - Option 2: Installing on a solid concrete or concrete  
block wall*  
CAUTION:To prevent property damage or personal injury, never drill into mortar between blocks.  
Mount wall plate directly onto the concrete surface.  
1
2
3
4
Align the wall plate template (R) at the height you determined in the previous step (or by using the  
HeightFinder mentioned on the template), make sure that it is level, then tape it to the wall.  
Drill pilot holes through the template to a depth of 3 in. (75 mm) using a 3/8 in. (10 mm) diameter  
masonry drill bit, then remove the template.  
Insert the concrete wall anchors** into the pilot holes and use a hammer to make sure the anchors are  
flush with the concrete surface.  
Align the wall plate (A) with the anchors, insert the lag bolts (P) through the lag bolt washers (O), then  
through the holes in the wall plate. Tighten the lag bolts only until they are firm against the wall plate.  
CAUTION:  
Avoid potential injuries or property damage!  
DO NOT over-tighten the lag bolts (P).  
**Not included. Call Customer Service to have the Fischer UX10 x 60 concrete anchor kit shipped directly to  
you.  
.
3 in.  
(75 mm)  
* Minimum solid concrete  
thickness: 8 in. (203mm)  
* Minimum concrete block size:  
8 x 8 x 16 in. (203 x 203 x 406 mm).  
* Minimum horizontal spacing  
between fasteners cannot be less  
than 16 in. (406 mm).  
** Note: Not  
See  
Note**  
See  
Note**  
included. Call  
Customer Service to  
have the Fischer UX10  
x 60 concrete anchor  
kit shipped directly to  
you.  
You’ll need  
Wall plate template (R)  
3/8 in. concrete  
drill bit  
O (4)  
1/2 in. socket  
wrench  
Wall plate (A)  
Drill  
P (4)  
Tape  
Hammer  
Level  
11  
 
FIXED-POSITION WALL MOUNT FOR TVs 40-70 in.  
STEP 6 - Mounting the TV to the wall plate  
1
Holding the TV with the top of the screen tilted toward the wall, slide the upper notches of the right and  
left TV brackets (B and C) over the upper lip of the wall plate (A).  
2
Push the bottom of the TV toward the wall until the latch mechanism clicks into place.  
B
C
A
HEAVY! You will need  
assistance with this step.  
&
12  
 
FIXED-POSITION WALL MOUNT FOR TVs 40-70 in.  
Removing the TV from the wall plate  
1
Grasp the TV by the bottom edge, then pull down on the locking cords and pull the bottom of the TV out  
from the wall.  
2
Release the locking cords and lift the top of the TV from the wall bracket.  
HEAVY! You will need assistance  
with this step.  
Unlatched  
Pull down to unlatch.  
Pull bottom away from wall,  
then lift off the wall bracket.  
13  
 
FIXED-POSITION WALL MOUNT FOR TVs 40-70 in.  
14  
 
FIXED-POSITION WALL MOUNT FOR TVs 40-70 in.  
One-year limited warranty - Insignia  
Definitions:  
The Distributor* of Insignia branded products warrants to you, the original purchaser of this  
new Insignia-branded product (“Product”), that the Product shall be free of defects in the  
original manufacturer of the material or workmanship for a period of one (1) year from the date  
of your purchase of the Product (“Warranty Period”).  
For this warranty to apply, your Product must be purchased in the United States or Canada from  
a Best Buy branded or Future Shop branded retail store or online at www.bestbuy.com,  
www.bestbuy.ca, or www.futureshop.ca and is packaged with this warranty statement.  
How long does the coverage last?  
The Warranty Period lasts for one year (365 days) from the date you purchased the Product. Your  
purchase date is printed on the receipt you received with the Product.  
What does this warranty cover?  
During the Warranty Period, if the original manufacture of the material or workmanship of the  
Product is determined to be defective by an authorized Insignia repair center or store personnel,  
Insignia will (at its sole option): (1) repair the Product with new or rebuilt parts; or (2) replace the  
Product at no charge with new or rebuilt comparable products or parts. Products and parts  
replaced under this warranty become the property of Insignia and are not returned to you. If  
service of Products or parts are required after the Warranty Period expires, you must pay all labor  
and parts charges. This warranty lasts as long as you own your Insignia Product during the  
Warranty Period. Warranty coverage terminates if you sell or otherwise transfer the Product.  
How to obtain warranty service?  
If you purchased the Product at a Best Buy or Future Shop retail store location, please take your  
original receipt and the Product to any Best Buy or Future Shop store. Make sure that you place  
the Product in its original packaging or packaging that provides the same amount of protection  
as the original packaging. If you purchased the Product from a Best Buy or Future Shop online  
and the Product to the address listed on the web site. Make sure that you put the Product in its  
original packaging or packaging that provides the same amount of protection as the original  
packaging.  
To obtain warranty service, in the United States call 1-888-BESTBUY, Canada call 1-866-BESTBUY  
for Future Shop call 1-800-663-2275. Call agents may diagnose and correct the issue over the  
phone.  
Where is the warranty valid?  
This warranty is valid only in the United States and Canada at Best Buy or Future Shop branded  
retail stores or websites to the original purchaser of the product in the county where the original  
purchase was made.  
What does the warranty not cover?  
This warranty does not cover:  
Customer instruction/education  
Installation  
Set up adjustments  
Cosmetic damage  
Damage due to weather, lightning, and other acts of God, such as power surges  
Accidental damage  
Misuse  
Abuse  
Negligence  
15  
 
FIXED-POSITION WALL MOUNT FOR TVs 40-70 in.  
Commercial purposes/use, including but not limited to use in a place of business or in  
communal areas of a multiple dwelling condominium or apartment complex, or otherwise  
used in a place of other than a private home.  
Modification of any part of the Product, including the antenna  
Display panel damaged by static (non-moving) images applied for lengthy periods  
(burn-in).  
Damage due to incorrect operation or maintenance  
Connection to an incorrect voltage or power supply  
Attempted repair by any person not authorized by Insignia to service the Product  
Products sold “as is” or “with all faults”  
Consumables, including but not limited to batteries (i.e. AA, AAA, C etc.)  
Products where the factory applied serial number has been altered or removed  
Loss or Theft of this product or any part of the product  
Display panels containing up to three (3) pixel failures (dots that are dark or incorrectly  
illuminated) grouped in an area smaller than one tenth (1/10) of the display size or up to  
five (5) pixel failures throughout the display. (Pixel based displays may contain a limited  
number of pixels that may not function normally.)  
Failures or Damage caused by any contact including but not limited to liquids, gels or  
pastes.  
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS YOUR EXCLUSIVE REMEDY  
FOR BREACH OF WARRANTY. INSIGNIA SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR  
CONSEQUENTIAL DAMAGES FOR THE BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON  
THIS PRODUCT, INCLUDING, BUT NOT LIMITED TO, LOST DATA, LOSS OF USE OF YOUR PRODUCT,  
LOST BUSINESS OR LOST PROFITS. INSIGNIA PRODUCTS MAKES NO OTHER EXPRESS  
WARRANTIES WITH RESPECT TO THE PRODUCT, ALL EXPRESS AND IMPLIED WARRANTIES FOR  
THE PRODUCT, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF AND  
CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN  
DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE AND NO WARRANTIES, WHETHER  
EXPRESS OR IMPLIED, WILL APPLY AFTER THE WARRANTY PERIOD. SOME STATES, PROVINCES  
AND JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY  
LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU  
SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE  
TO STATE OR PROVINCE TO PROVINCE.  
Contact Insignia:  
For customer service please call 1-877-467-4289  
INSIGNIA is a trademark of Best Buy and its affiliated companies.  
Registered in some countries.  
Distributed by Best Buy Purchasing, LLC  
7601 Penn Ave South, Richfield, MN 55423 U.S.A.  
©2014 Best Buy. All rights reserved.  
Made in China  
16  
 
Part # 6907-002071 00  
www.insigniaproducts.com 1-877-467-4289 (U.S. and Canada) or 01-800-926-3000 (Mexico)  
INSIGNIA is a trademark of Best Buy and its affiliated companies.  
Registered in some countries.  
Distributed by Best Buy Purchasing, LLC  
7601 Penn Ave South, Richfield, MN 55423 U.S.A.  
©2014 Best Buy. All rights reserved.  
V2 ENGLISH  
14-0745  
Made in China  
 

JBL Stereo Amplifier MXP1200 User Manual
JVC CD Player KD G305 User Manual
JVC Digital Camera TK C1481 User Manual
JVC DVD Player HR XVC11BJ User Manual
JVC DVD Player XV S300BK User Manual
JVC Home Theater System TH D5 User Manual
JVC Speaker System CA UXV100 User Manual
JVC Universal Remote CS HX6945 User Manual
KitchenAid Range KERS205TBL2 User Manual
Koolatron Refrigerator KWT10BN User Manual